How to Setup A Soaker Hose the Right Way? (10 Most Useful Tips)

 

The thing about soaker hoses is that they’re like a blessing in disguise. After all, it makes way for good, easy watering. And this is very useful if you have a large flower or vegetable garden. But not many who own a soaker hose know how to setup a soaker hose the right way.

If you want it to be an effective solution, then you need to understand how to connect soaker hoses. The instructions below may be a lot to take in. But once you get the hang of it, the task becomes much simpler, quicker, and more convenient. No two ways about that!

How to Setup A Soaker Hose the Right Way – 10 Most Useful Steps

#1 Begin with a level ground

The start of every soaker hose layout begins at ground level. Such hoses work flawlessly as a result of uniform water distribution. This means any slope is only going to mess with the uniformity. And when water is forced to only one area of the hose. Then there’s no point in using this particularly handy tool.

Just one patch of your garden receives water while the rest remains dry. That said, make sure the hose is on level ground. And not on hilly or rocky surfaces.

#2 Don’t use sprinkler connections

The sprinkler system consists of pressure that passes through it. But this pressure tends to be very high even for the best soaker hose. The pressure has the capacity to break down plastic and rubber materials.

So think twice before you use a sprinkler connection. Instead, go for your standard faucet. I’m sure you have one installed outside somewhere.

#3 Let the end cap stay on

When setting up a hose, it’s tempting to want to remove its end cap. You might think it harmless as taking off the cap means being able to see the flow of water. But you may want to leave it on. And here’s why. The water should remain trapped inside the conduit for seeping into the ground. It’s as simple as that.

#4 Fill up the hose entirely

What’s the primary purpose of a soaker hose? Forcing water through its tiny holes, right? Now if the hose itself is not filled entirely. Then how is any moisture going to get out? For that, you have to fill up the whole length of the hose with water. A full soaker hose has a standard cylindrical look. Meaning no flat or distended sections.

#5 Remove all disks except for the one at the water source

Don’t think of your hose merely as a conduit equipped with weeping holes. The length comes with restrictor disks crafted to work with the sources of water. The internal part here controls how much water enters the hose. And this paves the way for a more controlled soaking action in your garden.

But the majority of hose placement layouts demands different lengths attached together. So don’t skip the step where you have to take off the disks of other hoses. Just one disk is what remains at the end of the faucet for the purpose of pressure control.

#6 Use multiple water sources for covering a larger area

Needless to say, the design of the hose has certain limitations. It’s only logical to not exceed 150 feet when it comes to connecting lines. A hose longer than 150 feet is not able to soak your garden properly. It’s because that conduit loses its water pressure due to the long distance from the source of water.

So what do you do if you wish to cover an area larger than 150 feet? You use more than one water source.

#7 A higher water pressure is never the solution

Image name: soaker-hose-layout

Photo credit: http://www.mommysblockparty.co/

Here’s one of the most common mistakes people make when covering a larger area. And that is adding more water pressure into the system. Let me tell you that this isn’t the right solution for avoiding the limit of 150 feet.

You cannot force a higher pressure into the hose and still expect it to produce favorable results. What happens, at such times, is your hose starts to expand, much like a balloon. And this widens the holes too. The outcome of which is too much unnecessary water in your soil. Along with hose damage. The chances of your hose breaking or cracking are very likely here.

#8 Make sure the source of water is on a higher ground

If you want to know how to setup a soaker hose the right way, then pay attention to this. Gravity plays an important part in the setup. If your hose is running uphill, then it’s only common sense to assume that water is naturally going to flow downhill.

So how about choosing a source of water that is higher than your hose position on the ground surface? With such a setup, water leaving the spigot gets pulled downward by gravity. And flows along the entire length of the hose very smoothly. You get access to controlled seepage that means.

#9 Don’t over-soak or under-soak

Image name: how-to-connect-soaker-hoses

Photo credit: http://andiesway.blogspot.com/

Determining a suitable timing is a crucial part of the process. On top of that, soaking times tend to be slightly tricky. But the rule of thumb is saturating a garden for 200 minutes for a typical 5/8th of an inch hose. This saturates your garden with an inch of water. And most yards demand around 2 inches of water per week.

Other factors that matter in terms of determining watering strategies include landscaping obstacles, soil condition/type, temperature, etc.

#10 Test the hose before burying it in the soil

You have to test the system before you actually bury it into your soil. To test the hose, cover the thing up with mulch. This way water still gets to seep through without any difficulty.

You can coil your hose around a few plants. This enables saturating enough soil to initiate proper root absorption.

Conclusion

So I have addressed the most common problems that might arise during the installation of your soaker hose. How to setup a soaker hose the right way is not such a difficult or complicated process. You simply have to get it right the first time. And for that, these instructions/tips are the most helpful.

To nourish strong, deep roots, you have to open the gates to infrequent and deep watering. And it’s for this particular task that such hoses are manufactured. The perforated hose design allows water for seeping through. The water supply is slow and controlled, which also means no wastage.

pumparea
 

Click Here to Leave a Comment Below 0 comments

Leave a Reply: